Free panel calculator

How many acoustic panels do you need? Estimate it from four numbers.

Enter your room's size and echo time to see how many square feet of panels it takes to stop the ringing, and about how many 2 x 4 ft panels that is. It runs the same Sabine math Ryley Demers uses to size the custom panels he designs and installs.

RT60 calculator for acoustic panels

If the ceiling slopes, use the average height.
How long a clap takes to fade away. A free RT60 phone app gives a ballpark, or restaurants can ask Ryley for a free 60-second Sound Score at the door.

Your estimate

Fill in your room and press Estimate my panels. Your panel area shows up here in square feet, with a count of 2 x 4 ft panels.

The method

How the calculator works out how many acoustic panels you need

It uses the Sabine formula: echo time equals 0.161 times the room's volume, divided by its absorption (in metric units). Doubling the absorption in a room roughly halves its echo time.

  1. Your room's volume

    Length, width and height give the volume of air the sound has to fill. Bigger rooms need more panel area.

  2. Your echo time sets what is already there

    Echo time (RT60) is how many seconds a sound takes to fade away. Your number tells the formula how much your room already absorbs, so you never have to guess what the walls and floor are made of.

  3. Panels close the gap to the target

    The calculator counts each panel as fully absorbing (a coefficient of 1.0) and works out the area that brings your room to its target. It aims for 0.7 s in a restaurant, 0.6 s in a meeting room and 0.5 s in an open office.

  4. Add 15 to 20% for margin

    Panels cover some surface that was already soaking up a little sound. The margin covers that loss.

  5. Start with the ceiling

    The largest hard surface is usually the ceiling, so it gets panels first. Treating 25 to 40% of the wall and ceiling area is a common rule of thumb.

    Source: Commercial Acoustics, Reverberation Time for Different Rooms.

Your echo time

Three ways to get your room's echo time

The estimate is only as good as the echo time you give it. A phone reading is fine for a first plan, but a project is built on a calibrated microphone.

Free RT60 phone appSound Score at the doorSound Assessment
Who does itYou, on your phoneRyley, at Windsor-Essex restaurantsRyley, on site for 45 to 120 minutes
What it readsA rough echo timeOne clap, one echo timeEcho time by band from 125 Hz to 4 kHz, at 3 to 6 marked mic spots, plus background noise
How closeBallparkBallparkThe real number, measured with Room EQ Wizard and a calibrated mic
CostFreeFree, 60 seconds$249 home, $495 business (up to about 3,000 sq ft), credited to your project if you sign within 30 days

See everything the Sound Assessment measures or read how the Sound Score works for restaurants.

Example

A 1,200 sq ft café that rings for 1.3 seconds needs about 355 to 370 sq ft of panels

The café has an 11 ft ceiling, so the room holds 13,200 cubic feet of air. The goal is to bring the echo down to 0.8 s, inside the 0.5 to 0.9 s range for dining.

1.3 s to 0.8 s

Echo time today, and the target.

About 310 sq ft

Panel area from the Sabine formula, before the margin.

355 to 370 sq ft

With a safety margin added. That's about 44 to 46 panels of 2 x 4 ft.

Example only, worked with the Sabine formula. The calculator aims for 0.7 s in a restaurant, so the same café shows a larger number there.

Targets

The echo time each room should aim for

Hard-finish restaurants often ring for 1.2 to 1.6 s. Above about 1.0 s, guests start talking louder to be heard, which pushes the noise up even more.

These targets are measured at speech frequencies (500 to 1,000 Hz) in an empty room. A full room reads lower, because people absorb sound too.

See the room pages for restaurant acoustic panels and boardroom acoustic treatment.

Target reverberation time Typical untreated room
  1. RestaurantTarget 0.5 to 0.9 seconds.Typical untreated 1.2 to 1.6 seconds.0.5–0.9 s target · 1.2–1.6 s untreated
  2. Meeting roomTarget 0.5 to 0.7 seconds.Typical untreated 0.8 to 1.2 seconds.0.5–0.7 s target · 0.8–1.2 s untreated
  3. Open officeTarget 0.4 to 0.6 seconds.Typical untreated 0.9 to 1.2 seconds.0.4–0.6 s target · 0.9–1.2 s untreated
  4. Small theatreTarget 0.8 to 1.2 seconds.Typical untreated 1.3 to 1.8 seconds.0.8–1.2 s target · 1.3–1.8 s untreated

Reverberation time (RT60) at speech frequencies, empty room. Source: Commercial Acoustics, Reverberation Time for Different Rooms.

Home studios

Home studios get "Measure first" instead of a number

In a small room, most of the trouble lives in the bass.

Below about 200 to 300 Hz, one echo time number says little about a small room. So the calculator won't guess for a studio.

Ryley reads the bass with waterfall and decay graphs, then places panels and corner bass traps where they do the most. The goal is mixes that translate, in a room that still looks good to everyone else in the house.

How home studio treatment works

Questions

Panel calculator questions

How many acoustic panels do I need for my room?

It depends on the room's volume and how long it rings now. The calculator above gives square feet and a count of 2 x 4 ft panels. As a rough check, many rooms land at 25 to 40% of the wall and ceiling area.

What is a good echo time (RT60)?

For a restaurant, 0.5 to 0.9 s, with about 0.7 s as the sweet spot. Meeting rooms aim for 0.5 to 0.7 s and open offices 0.4 to 0.6 s.

Can I trust a phone app reading?

Use it as a ballpark. Phone apps and clap tests are good enough for a first plan. The Sound Assessment uses Room EQ Wizard and a calibrated measurement mic for the real number.

We want a lively room. Will panels make it dead?

Panels are sized to a target, so the room stops where you want it. For dining, 0.6 to 0.8 s keeps the buzz while guests hear each other without shouting.

Can panels go on the ceiling in a restaurant or office?

For businesses, Ryley documents the fire rating of the panel core and fabric, keeps panels out of exits, and plans around sprinkler heads, alarms and exit signs. Ceiling panels in a sprinklered space wait for a licensed sprinkler contractor's review. Your building and fire officials have the final say.

Can I hang the panels myself?

Yes. For smaller budgets, Ryley offers a measured placement plan and a panel kit you hang yourself.

Is this estimate real?

Close enough to plan with. A measurement gives you the real number.

The math is the Sabine formula, the same one I use to size your panels after I measure. Your echo time does the hard part, because it already counts every surface in the room.

A calculator can't see where each panel should go, how much your furniture soaks up, or what the bass is doing. Those answers come from measuring the room.

So I measure before I quote. I write the target echo time into your proposal, then re-measure after install from the same marked spots.

Turn your estimate into a measured plan

Bring your numbers to a free 15-minute call. I'll tell you if your room needs panels, a Sound Assessment or a plan you hang yourself. I measure rooms in Windsor, Tecumseh, LaSalle, Lakeshore, Amherstburg, Essex, Kingsville and Leamington.

Call Text Free consult